High-voltage and low specific on-resistance power UMOSFET using P and N type columns

For the first time, we present the unique features exhibited by power 4H–SiC UMOSFET in which N and P type columns (NPC) in the drift region are incorporated to improve the breakdown voltage, the specific on-resistance, and the total lateral cell pitch. The P-type column creates a potential barrier in the drift region of the proposed structure for increasing the breakdown voltage and the N-type column reduces the specific on-resistance. Also, the JFET effects reduce and so the total lateral cell pitch will decrease. In the NPC-UMOSFET, the electric field crowding reduces due to the created potential barrier by the NPC regions and causes more uniform electric field distribution in the structure. Using two dimensional simulations, the breakdown voltage and the specific on-resistance of the proposed structure are investigated for the columns parameters in comparison with a conventional UMOSFET (C-UMOSFET) and an accumulation layer UMOSFET (AL-UMOSFET) structures. For the NPC-UMOSFET with 10 µm drift region length the maximum breakdown voltage of 1274 V is obtained, while at the same drift region length, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 and 703 V, respectively. Moreover, the proposed structure exhibits a superior specific on-resistance (R_on,sp) of 2 mΩ cm², which shows that the on-resistance of the optimized NPC-UMOSFET are decreased by 56% and 58% in comparison with the C-UMOSFET and the AL-UMOSFET, respectively.     

How platinum oxide affects the degradation analysis of PEM fuel cell cathodes

In this work, proton exchange membrane fuel cell cathodes are degraded with accelerated-stress-tests.These PtCo containing cathodes are analyzed at begin-of-life and end-of-test with a dedicated diagnostic procedure. For every individual load point, the oxygen transport resistance and voltage losses due to the formation of platinum oxides were obtained in addition to commonly measured electrochemical surface area, high frequency resistance, as well as cathode ionomer resistance. These data were used to break down the voltage losses into six different contributors. With this break down, performance gains and performance losses were determined at end-of-test. At low current densities, it was found that voltage losses due to degradation are dominated by the loss of specific activity and catalyst surface area - in line with the state-of-the-art knowledge. But by quantifying the losses from platinum oxide formation explicitly, we show that end-of-test an unassigned voltage loss is not only present at highest current densities, but already at low current density. More precisely, the unassigned voltage loss shows a linear increase with decreasing half cell voltage and is independent from the chosen accelerated stress test. As this unassigned loss depends on half cell voltage, it might arise from ionomer adsorption.     

一种实现高压电容器带电倾斜旋转实验平台的研制

为方便高压电容器的性能评价实验，研制了一种高压电容器倾斜旋转实验平台，可实现电容器在高电压下带电旋转、带电倾斜等功能。试验场地的地面水平、通过测试线引入的电磁骚扰、高压连接线牵引应力等问题，在高压电容器的精密测量中，可能引入不可忽略的影响。本文对这些影响因素提出了解决措施，并基于试验平台，定量分析评价了试验场地不平对高压电容器电容量变化的影响，降低了高压标准电容器在高精度测量中的不确定度，为高压标准电容器的性能评价试验提供了重要的支撑。     

基于约瑟夫森量子电压的交流功率测量系统及方法研究

基于约瑟夫森量子电压标准设计了交流功率差分测量系统。通过分析差分采样系统的误差分布及误差传递函数,提出换向差分测量方法,减小了差分采样系统的增益误差,提高了电压幅值测量准确度;通过分析衰减系数η,证明了采用换向差分测量较容易实现10-7量级电压幅值测量。通过评估差分采样系统零相位,结果证明了差分采样系统具有较好的相位测量稳定性。分析了交流功率差分测量系统的不确定度分量,评估了功率因数为1.0,0.5 L和0.5 C时的功率测量不确定度,通过与国家交流功率基准装置进行实验比对,证明了基于约瑟夫森量子电压交流功率测量系统不确定度评估的合理性。     

融合前沿研究的液体电介质击穿教学研究

针对《高电压与绝缘技术》课程中液体电介质的教学难点，提出了融合前沿研究的液体电介质击穿教学方法。基于前沿的液体放电应用背景与先进的液体放电研究平台，形象地展示液体电介质的动态击穿过程，在教学内容、教学方法、考核方式等方面进行科教融合改进，实施“以学生为中心”理念的课程教学设计。该教学方式取得了较好的教学效果，能够为其它知识点的教学质量提升提供参考。     

Experimental investigation on the voltage uniformity for a PEMFC stack with different dynamic loading strategies

The operating life of the proton exchange membrane fuel cell stack is mainly decided by performances of its weakest single cell because of the “Buckets effect”, thus high voltage uniformity during a dynamic loading process is key to the stack durability. In this work, a 3-kW stack is examined experimentally on its voltage uniformity (voltage coefficient variation (Cv)) under conditions of loading from open-circuit state (0 A) to nominal current (165 A) and stack temperatures of 30 °C, 45 °C and 65 °C. Different dynamic loading strategies, namely constant loading rate strategy, decreasing loading rate strategy, and increasing loading rate (square/cube increasing loading rate) strategy, are examined and compared. Results display that during the loading process, (a) the voltage uniformity rises abruptly and goes down quickly when the loading current is small (e.g. from 0 A to 22 A), (b) the voltage uniformity under a small loading current is better than that under the open-circuit state, and (c) voltage uniformity decreases as the loading current increases from a small value to the nominal current. Comparisons of different current loading strategies show that as the stack temperature rises from 30 °C to 65 °C, the stack Cv value under the open-circuit state increases from 1.12 to 1.84 and decreases from 3.85 to 2.45 in the nominal current state. The maximum Cv for the decreasing loading rate strategy decreases from 16.25 to 9.49 and that of the constant loading rate strategy also decreases from 5.85 to 4.96. Cv values of the square current increasing loading rate strategy keep below 3.85 under conditions of the three stack temperatures and display a slight fluctuation during the whole current loading process, which indicates that the strategy can effectively make the stack being of an excellent voltage uniformity during the instantaneous response process.     

电压降法在水平定向钻穿越管道外涂层评价中的应用研究

介绍了电流-电位法、电流密度法在水平定向钻穿越管道外涂层评价中的应用,联合电压降法计算管内电流值,并结合实际案例对穿越管道两端连头之后外涂层性能进行评价。     

High performance multi-layer varistor (MLV) from doped ZnO nanopowders by water based tape casting: Rheology,sintering, microstructure and properties

In this work, we report the fabrication of a high performance multi-layer varistor (MLV) via water based tape casting method using novel compositions of nanomaterials. Bi₂O₃, CaO and Co₃O₄ doped ZnO nanopowders were prepared by solution combustion synthesis (SCS) route, calcined at different temperatures (550, 650, 750 and 850?°C) and characterized by TEM, XRD, SEM and AFM. The nanopowder (crystallite size ~30?nm) calcined at 650?°C for 1?h was used as the starting material for MLV fabrication. Compositions of the slurry containing doped ZnO nanopowders, binder and plasticizer in water solvent were optimized for the fabrication of thick film. The rheological properties of the slurries having different solid loadings were analysed and thick films of various thicknesses (50–500?µm) were prepared by varying the feeding rate of tape casting. The film roughness of 38.3?nm for the thick film made from 40?wt% solid slurry was found to be superior compared to other samples due to the presence of reduced crack and shrinkage. MLV fired at 950?°C for 1.5?h exhibited a coefficient of nonlinearity of 18 and breakdown voltage of 291.5?V that yields superior properties compared to commercial MLVs.